Page History: Parks 12" Planer Parts and Photo Index

Compare Page Revisions

81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Current 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

« Older Revision - Back to Page History - Newer Revision »

Page Revision: 2008/05/10 14:41

by Bill Nance

Introduction¶

The Parks 95 12" planer, as described on other pages within this wiki, is a well-respected vintage planer, manufactured across several decades by Parks Woodworking Machine Company, with a fairly consistent design throughout its history. This page provides an index of parts for a Parks Model 95 planer, including photographs and dimensions where available.

The original entry data and photographs are drawn from a restoration of machine #5401-, which is believed to have been manufactured in the early 1940s. The parts numbers are mapped to the exploded parts diagram and parts list from the 1949 Operating Instructions and Parts List for Parks 12" Thickness Planer found in the OWWM Publication Reprints. Others who wish to edit this entry with additional information should indicate in the comments section below any information that references a different operating manual. Please note that in the original entry, some parts were not included in the machine that was restored, and some parts were not disassembled and either may not be photographed or may be shown as a component of an assembly. Others are encouraged to edit/replace with individual parts as available.

Parks Model 95 Parts Index¶

Part#	Part Name	Dimensions	Qty	Comments
A1	Gear Box (Casting Only)	-	1	"Three hump" cast iron model
A2	Shaft Collar	.75"ID, 1.25"OD	3
A3	Hollow Head Set Screw	3/16" head	?
A4	12 Tooth Sprocket	.75"ID, 1.37"OD	2	2.25" exterior sprocket diameter
A5	Shaft Spacer	0.18" wide	1
A6	88 Tooth Gear, Slotted Hub	-	1	.75"ID
A7	Throw Out Sleeve Bearing	.75"ID	1
A8	Throw Out Sleeve	.75"ID, 1.125"OD	1	Sheeve: 1 5/32" inner diameter, 2" outer diameter
A9	Eccentric Bracket Studs	1"	2	1/4 20 threads
A10	Eccentric Bracket	-	1
A11	Throw Out Handle	~8"	1	curved handle version
A12	Throw Out Eccentric	see comments	1	main: 2.125" x .75"OD, flange: 1"OD, stud: .375" x .50"OD
A13	Lower Gear Shaft Bearing	.75"ID	1	part of lower gear shaft assembly
A14	88 Tooth Gear, Plain Hub	.75"ID	1	part of lower gear shaft assembly
A15	Short Gear Shaft	.50"OD and .75"OD	1	part of lower gear shaft assembly
A16	Gear Shaft Bearing	.50"ID	1	part of lower gear shaft assembly
A17	20 Tooth Gear	1.0"OD, ."ID	3	1.375" external tooth diameter
A18		-	1
A19		-	1
A20		-	1