Page History: Replacement Bearing List
Compare Page Revisions
Page Revision: 2014/01/14 08:14
Accurate Bearings comes highly recommended on the forum for replacements.
Boice-Crane
1400 6" Jointer
- 6203-LL (17mm B, 40mm OD, 12mm W)
1650 15" Bench Top Drill Press
Photo Index for this type drill pressThe following are the two upper bearings for the spindle. They are located just below the spindle sheave:
- 6005-LL (25mm B, 47mm OD, 12mm W)
- 6005-LLNR with Snap Ring (25mm B, 47mm OD, 12mm W)
Both of these bearings are available through Accurate Bearing.
Buffalo Forge
No. 18 Drill Press (w/ external screw table lift)
- Quill:
- Upper: 88505 ND > 88505 KS
- lower: 55505 ND > 5205 ZZ TS
- Pulley:
- Upper: 88508 ND > 88508 IF
- Lower: 88508 ND > 88508 IF
- Lift table:
- 5449 Nice > 3066 HV (3 required)
Craftsman
Shaper Model 101.09741
- Spindle:
- Upper: 6204-3/4 (19 mm bore and 47 mm OD)
- Lower: 6204-3/4 (These were difficult to locate. The Big Bearing Store carries them.)
Jointer Model 103.23340
- Cutterhead: R8ZZ both sides
Delta
Unisaw
- 87-010 Motor (x2):
- Original: Norma S 3505
- Replacement: KYK 63205
Note: I have a 1947 motor that says frame 180 Catalog No 87-010 and it takes New Departure 87504. Given this conflict with the above data it might be best to wait until the motor is open before buying bearings.
- Arbor (x2):
- Older style with narrow (~.325 in) spacers: 88503 (bearing has extended inner race)
- Newer style with wider (~.471 in) spacers: 6203 (bearing does not have extended inner race)
14" Drill Press (DP220)
- 2x 6202-10 (5/8" bore) for quill. These are not exact replacements as the original quill bearings were designed such that you could easily replace the quill with other designed for mortising or shaping, but for drill-only purposes these are suitable replacements.
- Pulley bearings are hard to find. Consider cleaning and reusing or ordering from Richard
15" Drill Press
- Quill - 2x 6203
- Pulley - 2x 6205
17" Drill Press
- Lower Spindle (Inside Quill) - 87503 (x2) (Early Production) or 6203 (x2) (Late Production)
- Upper Spindle Top Bearing - 487503 includes installed snap ring around OD
- Upper Spindle Lower Bearing - 88503
7" Tool Grinder
- Older Style:
- Newer Style:
- 2x48" Belt Attachment
10" Grinder
14" Bandsaw, Wood Cutting¶
- Newer Style:
- Upper wheel: 6202LL Nachi (2x)
- Lower wheel: 6204LL Nachi (2x)
- Blade guide thrust bearings: 6200LL Nachi (2x)
- Older Style:
- Upper wheel: 87502 (2x)
- Lower wheel: 87504 (2x)
- Blade guide thrust bearings: 6200LL Nachi (2x)
14" Bandsaw, Metal/Wood Cutting¶
- Older Style (w/ turn lever selector):
- Upper wheel: 87502 (2x)
- Lower wheel: 87504 (2x)
- Blade guide thrust bearings: 6200 (2x)
- Gear case: 87016 (4x)
- Input shaft oil seal: CR6229 (1x)
Delta/Crescent 20" Bandsaw (model 28-350 and 28-365 with rounded corner cabinet)¶
- Upper wheel:
- Lower wheel:
- Thrust bearings: 6203
Delta/Rockwell 6" Jointer (model 37-220)
- New Departure 87502
- New Departure 87503
- Extended inner race goes on cutterhead side
Delta/Rockwell 4" Jointer (37-290, 37-110, 22-110)
- New Departure 87502 (x2)
- Extended inner race faces the inside on both sides.
Super 900 - Radial Arm Saw
- Rollerhead (x4):Nachi 81004
Delta/Rockwell 22-101 Planer
- Cutter Head: 6205 (newer model w/ no extended inner race)
- Infeed/Outfeed Roller O-Ring: 22mm ID x 24mm OD (approximate)
- NICE thrust bearing in gear box #5774(2) required
46-111 14/11 Inch Lathe
- 87505 (x2) (extended inner race faces out on both sides)
43-503 Pin Router
- Spindle bearings
- 88504 20mm bore 47mm O.D. .6250 inch thickness
- 87501 12mm bore 32mm O.D. .500 inch thickness
Motor: Model 93-610 (2HP, 1725 RPM, capacitor start)
Motor: Model 87-310 (2HP 3 phase)
Motor: 3/4 hp 1725 rpm Repulsion Induction motor: frame 180
- Extended race face in: 87504 (x2)
Motor: Model 6400 - 1/3 hp 1725 rpm Repulsion Induction motor
- Extended inner race: 87502 (x2)
NOTE: Inner race is positioned toward the inside of motor
Motor: Model 62-110 - 1/3 hp 1725 rpm Capacitor Start motor
- Extended inner race: 87016 (x2)
NOTE: Inner race is positioned toward the inside of motor - Alternative: 6203 (x2)
My 62-110 used these.
Motor: Model 924 - 3/4 hp 1725 rpm Repulsion Induction motor
- Extended inner race: 87504 (x2)
NOTE: Inner race is positioned toward the inside of motor
Motor: Model 800 - 1/3 hp 1725 rpm Split Phase motor
- Extended inner race: 87502 (x2)
NOTE: Inner race is positioned toward the inside of motor
DeWalt
MBC/MBF 9" Radial Arm Saws
- Motor (1ph and 3ph):
- Arbor side: 88504
- Cord side: Original: Fafnir 200KLL2
- Cord side: Replacement: JAF 88500
(The GWI saw has the same motor bearings)
- Rollerhead (x4):
- Original: Fafnir 200KDD15
- Replacement: Nachi 81004
Oliver
192 18" Band Saw¶
- Howell Electric Co 1hp 3ph Motor:
Parks
12" Planer
M2 Bandsaw Wheels¶
- Upper - Originals 202KD, Replacement 6202ZZ
- Lower - Originals 204KD, Replacement 6204ZZ
Porter Cable
G4 Belt Sander¶
- Motor: 2x 6205
- Sander upper wheel: 2x5203 and 2x6203
Powermatic
141 Bandsaw¶
- Top: 2x 6203LLNR
- Bottom 2x 6204LLNR
- Guides 4x 6200LL
Sprunger Bros.
NDP15 Drill Press (floor and bench models)¶
link to photo index for this model machine
- Quill bearings: 2X 1623 Inch 0.6250" X 1.3750" X 0.4375" (double sealed or double shielded)
- Spindle drive bearings: 2X 6205 Metric 25mm X 52mm X 15mm (double sealed or double shielded)
Walker-Turner
14" Wood Bandsaw¶
- Upper Wheel: 6202 LL 5/8 bore
- Lower Wheel: 6204 LL 3/4 bore
Drill Press - Model 1100 20"
There are several variations of this press, some of which use Walker-Turner specific bearings (mostly with inch bores), some of which use standard bearings. Be careful when measuring!
- Pulley: 2x 6205
- Upper Spindle: 6204-3/4
- Lower Spindle: 5205 - not exact match, but close
- These are preliminary and have not yet been verified.
Early 700 Series 1/2" Shaper
Like this one
- Shaper spindle: 6203 (x2)