Image
Welcome Guest, • Login
RSS RSS

Navigation






Search the wiki
»

PoweredBy

Page History: Magnetic Starters

Compare Page Revisions



« Older Revision - Back to Page History - Newer Revision »


Page Revision: 2008/09/12 01:28



Executive Summary

The summary is at the beginning since you busy executive types may not want to read what turned out to be a rather lengthy wiki. So here is the “bottom line” for you folks:

  1. Plan to buy a used NEMA style unit. A-B 509 and 709 are good choices, as is the Square D 8536. Furnas, Westinghouse, GE are also popular. With other brands you are less apt to find the heaters you will need.
  2. Consult a NEMA table to figure out what size starter your motor needs. This is based SOLELY on phase, voltage, and HP.
  3. Buy a used NEMA style magnetic starter in that size. Don’t worry what size or how many heaters it has, if any. Also make sure the coil voltage on it is a voltage that you will have available in the enclosure it will go into.
  4. Consult the appropriate heater table to find the right size of heater you need for your model of starter, given your motor’s fully loaded Amps (FLA). Heaters from the major brands are still readily available used.
  5. If your unit didn’t come with pushbuttons or an enclosure, you’ll need to buy them too.
  6. Go read the Starter Wiring wiki.

Here is a common style older Allen-Bradley magnetic starter, their Model 709, in an enclosure. The main components are highlighted as follows:

contactor – blue. The bottom of the contactor is partly covered up by the pushbuttons.

heaters – red. Two are on one side, one on the other. Other manufacturers’ heaters are in line with the contactor rather than to the side.

coil – green. Connects directly into the contactor

pushbuttons – yellow. This unit is screwed onto the contactor. The actual pushbuttons are not visible in this photo, and are mounted on the front of the enclosure. They push against the two round nubs shown in the photo.

Allen Bradley Magnetic Starter 709

Allen Bradley Magnetic Starter 709


Magnetic Starter Tutorial

You probably wound up here because you need to buy “something” to turn on the motor on your machine, or perhaps you have bought or scrounged a used “something” and realize that you have no idea if it’ll do the job, or maybe you are changing your machine to use a new motor with a different voltage/phase and are not sure if the existing “something” can do the job. I recently went through the same experience. I bought a new motor with different voltage, phase, and HP specs from the original in my planer, and wound up spending more on a new Magnetic Starter than the motor cost me! That was a rude shock. Second time around I got a bit smarter, understanding more of what I needed, I was able to get what I needed used off eBay for way cheaper.

OWWM wisdom is that setting up the Starter, running the wiring, and spec’ing and mounting the motor can often be a bigger chore than restoring the machine itself!

(Note that there is a seperate wiki on wiring a magnetic starter, please refer to it for more details on the wiring.)

Let me first state that I am by no means an expert on magnetic starters. Having just recently gone through the experience that you are in the midst of, I hope that by laying out what I learned along the way your path the understanding what you need will be smoother (and cheaper!) than mine was. I hope that this wiki will serve as a starting point that others with more expertise in the area will add to. If you find any errors or missing information in this wiki, please feel free to make any changes you feel are needed!

Definitions

First, we need to settle on some definitions before we dive into the details. A lot of people play fast and loose with the terminology of starters.

Relay

A ubiquitous electrical component that typically consists of a coil and one or more sets of contacts. Normally a lower voltage/current is applied to the coil, closing (turning on) a higher voltage/current circuit through the contacts. Your car is full of relays, so is your washing machine. Any time you hear an electrical device make a ‘click’, that’s probably a relay. The main component of a Magnetic Starter is a big relay called a Contactor, which is controlled by a second smaller relay.

Disconnect

A separate item from the Magnetic Starter. Normally a big box with a handle on the side that completely disconnects (hence the name . . .) a circuit from the power. Apparently required by some electrical codes in addition to the breaker box on your wall and the starter on your machine. Completely unrelated to turning your running machine on and off, and despite their impressive heft, in fact they are not designed to do so and will not last long if used for this purpose.

Phase

The power in your shop will be either single phase or three phase, usually single phase unless you are in an industrial location. Your motor may require single or three phase. (Creating three phase from single phase is way beyond the scope of this wiki, and will not be covered here.) Motor Starters are normally designed for three phase operation, a few are designed for single phase operation.

Three phase Starters can be used in single phase applications, but the converse is not normally true, unless it was originally a three phase device used in a single phase situation, then it could be re-purposed to a three phase environment! (Don’t worry, it won’t get any more complicated than this!)

If you have a single phase motor, you don’t need to get specifically a single phase Starter. The selection of three phase starters is way larger, and wiring them up for single phase is trivial, so go ahead and get a three phase Starter.

Note that there is some controversy in the forums regarding how many heaters are needed when using a three phase starter in a single phase application. Some feel that only one (the hot) leg needs a heater, others feel both should have one. Some contactors may require all three heaters be in place to function, while the rating and thus proper operation of the heaters may be predicated on all three being present. So bottom line is that heaters are cheap. Use three even if you are single phase and you’ll never have to worry.

(We are getting ahead of ourselves here, but he A-B 509's require that all three heaters be present since they share a common trip mechanism. The older 709's had overloads that were discrete.)

The heaters being in close proximity with each other are going to affect the trip points. If one has no current flowing through it, it will not be heated and may affect the trip point of the other two. AB always indicates that three heaters still be used in a single phase application. For the 509's, you have to have the position occupied anyways, you might as well wire through it as they indicate.

Switch

This is what you use to turn on the lights in your shop. The word “switch” is never used to describe the Starter that turns on your machine. A Magnetic Starter (or Manual Starter) is not a “magnetic switch”. Get that word out of your head right now! It’ll just cause confusion for you. That’s the first thing a newbie should learn, and I will confess without shame that I used the term “switch” in my first post on the subject in the forums.

However, if you have a fractional horsepower motor, up to 1 HP or maybe 1.5 HP, then you can probably get away with a sturdy double pole, single throw 30 amp minimum switch. Be aware that a toggle type switch offers no overload protection, or automatic shutdown in the event of power loss. If you use one of these for a motor running at 220VAC or greater (i.e. both leads to the motor are hot), it must be of a two pole type. A single pole type is only for use at 120VAC and the switch must break the hot lead (usually a black wire), not the neutral (usually a white wire).

Manual Starter

A manual motor starter usually has 2 or 3 pushbuttons; start, stop and sometimes a separate reset button. Sometimes the reset is combined with the stop button. These starters require mechanical action (you pushing the start or stop button) to close or open the contacts on the starter's contactor. Manual starters usually contain "heaters" which are overload protection devices that will automatically (by mechanical means) open the contacts in the event that the motor draws too much current. The heaters must be sized for the full load operating current of the motor for the voltage that you are operating the motor at. A manual starter will remain on if you have a power failure, so when the power comes back the motor will start without you doing anything, making them inappropriate from a safety perspective for most of our woodworking machinery.

Magnetic Starter

A magnetic starter is similar to a manual starter except that it uses a relay to connect the contacts. The pushbuttons that control this relay are actual low current momentary contact switches. Pushing the start button energizes the relay and starts the motor. There is a "holding" contact on the relay which keeps it energized until something else interrupts the current to the relay such as pushing the stop button or if there is a power failure. You have to press the start button again after a power failure to start the motor. Magnetic starters usually have heaters which function as described in manual starters above.

A Magnetic Starter consists internally of a contactor, heaters, coil and control circuit, pushbuttons, and an enclosure. The pushbuttons may or may not be in the same enclosure, and some or all of the starters components may be integrated together. Sometimes it’s just called a Starter, or a Motor Starter, or a Magnetic Motor Starter. It is NEVER called a Switch.

Contactor

This is the heart of the Magnetic Starter. I like to think of it as a hopped-up relay. It’s the part that closes the circuit to your motor, allowing current to flow and the motor to run. It has a set of contacts for controlling the power to the motor, normally three, sometimes two. It also has a coil, such that when power is applied to the coil by the Auxilliary Circuit, it will cause the contacts to close. Sometimes the contactor is incorrectly referred to as a Starter. It is only one component of a starter. This misleading description is common on eBay.

Note that NEMA contactors frequently have their “ratings” printed on them in addition to their size. This is unnecessary, since the NEMA size will fix the ratings of the contactor. Thus, the printed ratings are redundant, and simply taken from standard NEMA tables for that size.

Heater

Also called Thermal Overloads, Thermal Overload Relays, Overload Heaters, or simply Overloads. These are basically simple heat sensitive circuit breakers that are matched to the current draw of the motor, and plug into or otherwise attach to the contactor. They will trip if their temperature rises above a certain level, due to excessive current passing through them. Heaters sense current, not voltage.

Note that if the heaters trip, the control circuit is cut, not the motor circuit directly. The control circuit being cut causes the contactor to drop out and cut the motor power. So it is an indirect effect.

They may seem redundant, after all you have a circuit breaker box in your house/shop that protects everything, so why do you need another? The reason is the circuit breakers in your house are designed to protect the wiring in your house, and by extension the house itself. The heaters in your Magnetic Starter are designed to protect your motor. Heaters are designed to mimic the characteristics of a motor in use(“eutectic”) and have similar heating characteristics. Motors can tolerate short term overloads without damage. These overload conditions can persist far longer than a typical circuit breaker or fuse can tolerate at a similar condition, that’s why we use heaters instead of a similarly sized fuse or circuit breaker. You want your heater to trip the overload before you smoke the motor!

eBay listings frequently describe contactor/heater combinations as starters, which is not completely true, as they are only part (granted a major part) of a full starter.

Heater sizing is interesting, they are not specified in Amperes like fuses or household circuit breakers are. Rather, each manufacturer has one or more “series” of heaters. Each series is typically used in conjunction with multiple models and sizes of contactors. Each heater has a number, e.g. N-38, and you must use a table supplied by the manufacturer to determine the correct heater for your motor, based on the motor’s current and the contactor’s NEMA size. For example, the N-38 heater is rated at 23.6 Amps with a NEMA size 3 contactor, but only 19.1 Amps with a NEMA size 1 contactor. Also, different series’ within a single manufacturer have different ratings for the same numbered heaters. For example, an A-B N38 has a different rating that an A-B W38.

Different tables are used for heaters in an open starter vs one in an enclosure. Even the type of enclosure has an effect.

Here are a couple examples of common heaters.

Different AB Heater Styles (Class 10, 20, and 30)

Different AB Heater Styles (Class 10, 20, and 30)

Furnas Heater

Furnas Heater


Control Circuit

This is the circuitry that supplies power to the coil in the contactor to close the circuit to the motor (turn the motor on), and removes power from the coil to open the circuit to the motor (turn the motor off). It contains a small relay that latches the circuit on. Be careful when spec’ing your contactor, that you get a coil rated at the voltage you need. For example, you can typically get 240V, 120V, or 12V coils in a given contactor, and other voltages such as 440V and 575V are also available. Note that the auxiliary circuit normally uses only a small amount of current, thus requiring small wires.

Pushbuttons

A Magnetic Starter typically will have ON and OFF pushbuttons, sometimes a Reset too. These are part of the Control Circuit. These will be momentary contact, ON being Normally Open and OFF being Normally Closed. Momentary contact means that contact is made only as long as the button is pushed. This is quite different from a light switch, where the contact remains in position until the switch is flipped again. No need to hold the light switch in position for the lights to remain on. . . (the auxiliary relay in the control circuitry provides the latching function so the motor stays on after you release the ON button)

A Normally Open pushbutton (such as the ON in our Magnetic Starter) would normally not allow current to flow through it (i.e. it’s “open”), and would allow current to flow only so long as it was pressed. A normally closed button is the opposite. The Pushbuttons may be mounted in the same enclosure as the Contactor and Heaters, or may be mounted remotely. In that case they can be more correctly called a “remote control for a mag starter” or sometimes a “pushbutton station”. In industrial applications there may be pushbutton stations in several locations.

Separate Pushbutton Station

Separate Pushbutton Station

Older Enclosure With Integrated Pushbuttons

Older Enclosure With Integrated Pushbuttons


Note that the pushbuttons do not carry the full load of the motor’s current. So they are electrically speaking quite light duty devices. You have wide latitude in selecting the pushbuttons for your system, as long as they were designed for the coil voltage you will use, you should be good to go.

The Coil “Thing”

The coil is a key component of a Magnetic Starter. Electrically, it is part of the Control Circuit, in fact it is what the control circuit controls. Physically, it is located in the contactor. Contactors are rarely ever sold without a coil in them. When you push the “ON” button, the contactor’s coil is energized, causing the contacts in the contactor to close. At the same time a separate smaller relay sometimes called the auxiliary contact or auxiliary relay is also energized. This relay is electrically in parallel with the “ON” button and stays closed when you release the “ON” button, keeping the coil energized and thus the main contacts closed. Similarly, when you push the “OFF” button, the auxiliary contact is de-energized and opens, causing the coil to be de-energized, and the main contacts to open and the motor to coast to a stop. The auxiliary circuit uses only a small amount of current, and is separate from the main circuit.

The key thing to understand is that a coil is rated at a specific voltage. So when you buy your starter, make sure the coil has the right voltage. Usually “the right voltage” means the same voltage as the motor. One exception might be in a 240V situation, if the neutral line is also brought into the enclosure, then 120V will be available so either a 240V or 120V coil would work. (Never use ground in place of neutral.) Another exception would be if the pushbuttons are to be really remote from the rest of the Starter, 24V might be a safer choice.

Coil voltage is particularly important if you are dropping a new starter into an existing pre-wired enclosure. If your coil is rated at a voltage that you don’t have in the enclosure you’re either running a new cable to the enclosure, fiddling around with a transformer, trying to dig up a suitable coil, or buying a whole new starter. These scenarios are easy to avoid with a correctly rated coil. Coils can normally be replaced with one of a different voltage rating, but replacement coils are not nearly as widely available as heaters.

NEMA

National Electrical Manufacturer’s Association. Years ago they defined a set of standards for Magnetic Starters, in particular contactors. The standards are pretty simple to understand, and widely used in the US and Canada. NEMA Contactors are designed to be specified based on phase, voltage and horsepower. They are sufficiently overbuilt to handle a wide variety of applications. NEMA Heaters are spec’ed based on the full load current of the motor. You figure out the size contactor you need based on phase, voltage and HP, then figure out the size heater you need for the contactor you have chosen based on the full load current. All NEMA contactors of the same size have the same ratings, regardless of what may (or may not) be printed on them.

IEC

The IEC is the International Electrotechnical Commission. This is another specification for Magnetic Starters, very popular in Europe and now in Asia. Most of the cheap Chaiwan machines use IEC starters on them. In fairness, companies like Siemens and Moeller make good quality IEC starters. NEMA and IEC do not directly cross match. It’s not like pounds and kilograms or Farenheight and Celcius. IEC spec starters may not have heaters, rather Instead of heaters, the overcurrent rating can be adjusted within the specified range of the device, via a built-in potentiometer type control.

A very good explanation of the differences between IEC and NEMA can be found here.

Many OWWM’ers prefer the more robust NEMA style, and think they look more appropriate on the older machines. However, new NEMA starters are not cheap. Oftentimes an import IEC Starter will be available at a very appealing price. But, there are http://www.sawmillcreek.org/showthread.php?t=71086 with these inexpensive Starters.

One OWWMer summed up his experiences with IEC starters as “I would not trust them as far as I can throw them. And I have thrown them.”

What does a Magnetic Starter do?

There are several important tasks that the Magnetic Starter performs.

Obviously, it safely starts up the machine. And, it does this is such a way that it minimizes arcing of the contacts, and danger to the operator. A ‘switch’ as we commonly know it would be destroyed quickly by the arcing caused by the high start up currents of our motors. To minimize arcing a starter uses a low current control circuit to turn the contactor on quickly, and also the physical area of the contacts is large, further reducing arcing.

It will also protect your motor from drawing too much current. For example: If your motor draws 9 or 10 amps and it gets a jam, low voltage condition, or other anomaly, it has to sit there locked up till the amps get high enough to trip the circuit breaker that is in the main panel. By that time the motor might be fried. The heaters in the motor starter are sized according to the amps the motor draws. They monitor the current flow so if the amps go up even slightly they will open a set of contacts and shut off the motor.

Another important task that the Magnetic Starter does is when power is interrupted for any reason, heater-overload, lightning, plug pulled, power outage, etc, it will automatically ‘turn off’ and prevent the machine from restarting when power re-appears. In other words, the switch STAYS off until the operator physically turns it on again. (Note that a manual starter will not do this, a crucial difference.)

Another advantage is that the pushbuttons may be mounted remotely from the starter itself.

What do I need for my machine?

This is really why you are here isn’t it? So, having read all the background info, what do YOU think you need?? If you answered “a properly sized contactor, properly sized heaters, a coil with the correct voltage rating, pushbuttons, and an enclosure”, you would be right! Let’s look at a couple ways to get what we need, going with a new IEC starter, or going with a used NEMA starter. you could go with a new NEMA starter as well, but that is a less popular choice with OWWM'ers, as you can get the same thing used for way less on ebay, plus you get the period looks as well.

The first thing to do is to look at your motor plate and note the phase, voltage, horsepower, and the fully loaded current draw (FLA). Let’s say for example that you have a 230V 3 HP single phase motor that draws 19.0 Amps fully loaded, such as the one in the photo below.

Example Motor Specs

Example Motor Specs


I Want the Cheapest Starters I Can Find

These will be your Chaiwanese built IEC units. Go to the Grizzly website for example, search for Magnetic, have a chuckle that they are called “Magnetic Switches”, then select the ones that are rated for your requirements. They have the exact units you will need, single phase starters rated for 220V (same as 230V) and 3 HP. You are good to go until they stop working.

They have cheesy, flimsy plastic boxes that are hard to mount without a little support rigging. If you try to get too low on the heater amp adjustment, they may cut out. Mid range and up, they work fine and last if you never smack one hard turning around with a long 4 x 4 or the like.

I Want a Used NEMA Starter

There are several steps you need to take in the process of finding the right starter for your situation. Be aware that, as with anything bought used, there is the chance that it might not work. In that case, unless the buyer offers returns, then you will be out of luck. That being said, these old contactors are well built and the biggest problem typically is the contacts can wear due to arcing, and are thus in need of polishing or rarely, replacement.

Step 1 – Determine the NEMA Size You Need for Your Motor

NEMA starters (actually just the contactors) are selected based on phase, voltage and HP only. You can use NEMA tables to help you decide what you need. For three phase, select the “Full Voltage Starting” column.

So, if you are wanting to run the example 240V 3 HP single phase motor, you can see that the NEMA 1 sized starter is rated for 3 HP in 240V single phase scenarios. It’s as easy as that. Any NEMA size 1 starter from any manufacturer will do. FLA does not matter, any current rating or other mumbo jumbo printed on the unit does not matter.

Step 2 – Find a NEMA 1 Unit

There are several suppliers who specialize in the older NEMA style starters. There are other suppliers mentioned in the forums as well, these ones came to hand as this wiki was being written.

Southland Electrical has received many favorable reviews on the forums.

Power Equipment Sales Company, and Mag-trol (ask for Lars), CPI Surplus and Automation Direct are also popular suppliers. They can probably find a complete NEMA unit to meet your requirements.

Alternatively, eBay is a great place to buy what you need. It’ll take a little more work, but it can be much more economical, and you’ll learn a lot. Search for Magnetic starter, motor starter, NEMA 1, etc.

You will quickly notice that your ebay searches will turn up a wide variety of sizes, ages, and styles (IEC/NEMA) of units. As one OWWM’er put it “the dizzying array of manufacturers and models is, well, dizzying”. Some units will be more complete than others, as will the information and photographs provided by the seller. It is unlikely that you will find a complete unit with the correct size heaters for your application. That’s OK, heaters are cheap and readily available. It is more important that you select a proper NEMA size unit for your application (in our example’s case, NEMA 1) and with a suitable coil voltage (240V preferred, 120V OK).

You will also notice that some manufacturers’ devices are more widely available than others. In particular Allen-Bradley 509 and 709 and Square D 8536 are easy to find, and to a slightly lesser extent Furnas ESP 100, GE and Westinghouse. The A-B 509 is a more modern unit (80’s?), the 709’s are older.

The A-B 500 series (“Bulletin 509 Starters” in the A-B nomenclature) numbering system is explained here. The Model number will give you an indication of how the starter was supplied from the factory, but many parts can get changed, added, removed, etc. over time. Note that many starters which were originally supplied with enclosures are offered for sale after being removed from the enclosure. Also notice that NEMA specifies enclosure “type” as well as contactor size, but the type is generally not important to OWWM’ers.

It hasn't been too many years back that 3 phase magnetic starters used only two heaters. If the motor was overloaded the two heaters opened and the starter clicked off. Now three phase magnetic starters use three heaters, but you may come across some units configured in this older style.

So here is a starter that might be suitable for our example motor. It’s a NEMA size 1 with three N-14 heaters and a 120V coil. It also includes the pushbutton, and an enclosure painted back in the day by a 3 year old with fingerpaints. This is nice because it includes everything we need, except that the heaters are the wrong size, and the paint is not to everyone’s tastes. That’s OK, heaters are cheap and readily available.

Notice that the heaters kind of hang off the side of the contactor. This is typical for the A-B units.

Complete A-B Starter

Complete A-B Starter

 A-B Starter Detail Showing Coil Specs

A-B Starter Detail Showing Coil Specs

 A-B Starter Enclosure

A-B Starter Enclosure



Step 3 – Determine What Size Heaters You Require

To choose heaters you need to know what contactor you will be using. In this example, it’s an A-B 709 series. You can see from looking at the pictures that it comes with N-14 heaters. We can consult a heater table such as the one http://www.southlandelectrical.com/AllenBradlyHeaterTables.asp?url=IND for the A-B “N” series to determine that the N-14 heater in a NEMA 1 starter are rated for only 1.98 Amps. Clearly this is inadequate for the 19 Amp motor! The same table shows that for 19 Amps an N-38 heater will be required. A search on eBay shows heaters available from numerous suppliers for under $3 each.

So our work is done here. Time to consult the wiring wiki!

I Have This Old Starter I Scrounged Up , Can I use it?

Unless it is one of the popular models that has a wide variety of heaters available for it, it is unlikely you will be able to use it. Even if the contactor happens to be a suitable size, you will have a very difficult time finding the heaters you need.

But, assuming you have a popular brand, what is its NEMA size? It’s pretty easy to tell with the older NEMA units. Look at the contactor of the unit you want to use – the NEMA size will be printed right on it. Then use the NEMA table referenced at the top of this wiki to determine what NEMA size your motor requires. So. Is the starter you dug up the right size for your motor? Recall our example motor requires a NEMA 1 unit. If you are holding a smaller unit such as NEMA 0 or NEMA 00, then the answer is No you can’t use it.

What about if you are holding a bigger device, such as a NEMA size2? Normally you would not use a larger NEMA size than you need since they are generally more expensive than the smaller ones. However, if you already have it, you still may be able to use it as long as it’ll support the right size heaters. So if we think back to our example motor of 19 Amps which needed the N-38 heater in the NEMA size 1 enclosure, by consulting the A-B heater tables again, we can see that for a NEMA size 2 contactor, we will require an N-37 heater. Not dramatically different in this case, the problem really lies at the lower current levels, where a NEMA size 2 contactor will not operate at all under 5.3 Amps.

Unless you are remarkably lucky, the heaters that came with the starter you scrounged up will probably not be the right size. Whether it came with heaters or not doesn’t really matter, you should expect to have to buy the right size ones. What about the coil, is it a voltage that you can supply? If it’s a 440V coil you are looking at some extra work/cost that can be easily avoided by using a different coil or a unit with a different coil. Luckily, most used starters for sale these days seem to come with 240V or 120V coils.

Don’t forget you’ll need pushbuttons and an enclosure too!

Here’s one example.

MTE IEC Type Starter

MTE IEC Type Starter

MTE IEC Type Starter

MTE IEC Type Starter

MTE IEC Type Starter

MTE IEC Type Starter



It came from a jointer that used this motor on it. It’s a 575V 3 phase 5 HP motor that draws 5.6 Amps.

WEG Motor Plate

WEG Motor Plate



The unit is an IEC starter of unknown age, made in England (really!) by a no longer extant company called MTE, perhaps it’s 80’s vintage? It’s IEC category AC-3 which is the appropriate category for most woodworking applications. This does not relate in ANY way at all to NEMA size 3. It is rated for a max of 4Kw at 240V. Our motor is 3 HP, which converts to 2.24 Kw, so at first blush things look OK. The overload on it is a 01000130-009. But, looking at the table that is on the inside of the starter enclosure, we can see that this overload is spec’ed to a range of 5.4 – 8.0 Amps. That is insufficient for our 19 Amp motor. In fact, the table seems to indicate that the largest overload suitable for this contactor can only handle 18A. Since this is such an obscure starter, we have no way of determining if larger overloads were made for it. And none are available on eBay or anywhere. So this unit cannot be used with our 3 HP 240V motor.

In addition, the contactor is wired for 575V control, so even if the contactor and overload were suitable for the current of the 240V motor, it is unlikely that the coil would work at 240V. A transformer could be used to step up from 240V to 575V, but you will note that there is no space in the enclosure for a transformer.

A couple of interesting notes on this device. Its compact size is typical of IEC starters, everything is in a single enclosure that is small by NEMA standards.

Note also that the contactor’s power rating actually increases as the voltage goes up. The interesting flip side of this of course is that when changing a motor out to a smaller one that runs on lower voltage, often the contactor will not be able to handle the lower voltage and horsepower! This is true of NEMA starters as well.

Lastly notice that the overload actually has a small white slider on it that will allow the overload current to be set quite precisely anywhere in its range or 5.4 to 8 Amps.

Other Example Starters

Here’s another AB unit. It’s a NEMA size 2 and has what look like three N-33 heaters on it. Can’t tell from the photo what the coil voltage is, the red printing that is obscured by the camera flash would normally show it, but red printing on an AB starter means a 120V coil (208v is black, 240v is green). Also, there is no pushbutton or enclosure with this unit.

A-B NEMA Size 2 Starter

A-B NEMA Size 2 Starter



Here is a Westinghouse NEMA size 0 unit. It has three FH27 heaters on it. Notice that they are positioned directly below the contactor like an AB 509 rather than to the side as are the AB 709 heaters. It does not have the coil voltage printed on it, but the vendor helpfully states “I assume that the coil is 230Volt because that was the voltage it was hooked up to”.

Westinghouse NEMA Size 0 Starter

Westinghouse NEMA Size 0 Starter



Here is a photo of a Cutler Hammer starter. This is a more complete unit, with the housing and pushbuttons, and there does appear to be a separate heater block below the contactor. Otherwise, it’s hard to get much info from the picture. The vendor states “A Used CUTLER-HAMMER CH Motor Starter With Enclosure... VERY Heavy Duty... 600VAC... Coil Voltage Is 208V 60HZ... 3 Thermal Protector Heaters # 1026... Heaters Are Rated From 2.73 To 3.04 Amps... 3 Heaters With Reset.” He does not state what NEMA size it is. The small heaters could indicate that it was originally used at about 3hp if the voltage was 575v, or about 1hp at 240v. 208 volt is a three phase (3ph) Wye specific voltage. Although it is not recommended, this coil will function with single phase 240 volt supply, albeit you may shorten it's life.
Cutler-Hammer NEMA Size 0 Starter)

Cutler-Hammer NEMA Size 0 Starter)



Here is a GE starter. This one is interesting because it only includes two heaters, the place where the third heater would normally go is simply shorted. Vendor states it is NEMA size 1, has a 120V coil, and gives the heater size. Possibly used in a 120V single phase application, got away with only two heaters instead of three. Again, pushbutton and enclosure are not included.

GE NEMA Size 1 Starter

GE NEMA Size 1 Starter



Here is a Square D starter. It is a NEMA 1 with 120V coil. Can’t tell exactly what size the heaters are, might be S19.5, but new and correct sized Square D heaters are easily obtained.

Square D NEMA Size 0 Starter

Square D NEMA Size 0 Starter



Here is a more modern Cutler Hammer starter. It shows clearly on it that it is NEMA size 0. It has three heaters which may be set to one of four current settings. Kind of a transitional type of heater between the single value heaters of old, and the potentiometer adjustable heaters on today’s starters.

Cutler-Hammer NEMA Size 0 Starter

Cutler-Hammer NEMA Size 0 Starter

Cutler-Hammer NEMA Size 0 Starter

Cutler-Hammer NEMA Size 0 Starter



Other Issues

Heater Class

The "Class" of a heater designates the trip behavior in terms of the time constant.

Class 10 will trip in 10 seconds at 600 percent of its rating. Class 20 is 20 seconds, class 30 is 30 seconds. This designates one point on the curve but it also determines the overall shape of the trip curve.

General purpose overloads are usually Class 20. In the A-B world (Bulletin 509 starters), this would be a Type W. If you want Class 30, you would sub a Type WL. For Class 10, you would use a Type J.

Class 10 overloads are usually used for hermetic motors that cannot stand a high degree of overload. Class 30 are used for high inertia loads. A big direct drive band saw may actually fall in to a Class 30 designation. One can start with class 20 for general needs. If the machine trips at startup, with properly sized heaters for the motor, then look at class 30's. This is preferable to up-sizing the heater to accommodate a hard start.

A-B Heater Interchangeabilty

There is some scuttlebutt on the forums that A-B’s type W and N heaters do offer a degree of interchangeability, easily in one direction and with modifications in the other.

NEMA Style

While NEMA size refers to the electrical “size” of the contactor as described in the previously referenced NEMA tables, NEMA style refers to the size of enclosures used to house Starters.

ScrewTurn Wiki version 3.0.5.600. Some of the icons created by FamFamFam.