Parks 12" Planer Parts and Photo Index

Modified on 2013/10/28 11:32 by Bill Nance Categorized as Maintenance, Restoration Topics
''by [http://www.owwm.com/members/detail.aspx?id=4047|Bill Nance]''



==Introduction==
The Parks 95 12" planer, as described on other pages within this wiki, is a well-respected vintage planer, manufactured across several decades by Parks Woodworking Machine Company, with a fairly consistent design throughout its history.  This page provides an index of parts for a Parks Model 95 planer, including photographs and dimensions where available.  

The original entry data and photographs are drawn from a restoration of machine #5401-, which is believed to have been manufactured in the early 1940s.  The parts numbers are mapped to the exploded parts diagram and parts list from the [http://www.owwm.com/files/PDF/Parks/ParksPlaner.pdf|1949 Operating Instructions and Parts List for Parks 12" Thickness Planer] found in the OWWM Publication Reprints.  Missing parts or photos were kindly provided by Doug Rewerts, resident OWWM Parks guru.  Wiki contributors are encouraged to edit/replace with individual parts as available/appropriate, but are also requested asked to please indicate in the table's comments section any information that references a different operating manual. 

===Parks Model 95 Parts Index===
{| width="100%" cellpadding="3"
| '''Part#''' || '''Part Name (click part for photo)''' || '''Dimensions''' || '''Qty''' || '''Comments'''
|-
| A1 || [{UP}Parks12InchPlanerParts%2fP95_A1_gearbox.jpg|Gear Box (Casting Only)] || - || 1 || "Three hump" cast iron model
|-
| A2 || [{UP}Parks12InchPlanerParts%2fP95_A2_shaftcollar.jpg|Shaft Collar] || .75"ID, 1.25"OD || 3 
|-
| A3 || [{UP}Parks12InchPlanerParts/P95_A3_hollowseadsetscrew.jpg|Hollow Head Set Screw] || 3/16 head, 3/8x3/8 || ?? || 3/8 16 thread
|-
| A4 || [{UP}Parks12InchPlanerParts%2fP95_A4_12toothsprocket.jpg|12 Tooth Sprocket] || .75"ID, 1.375"OD || 2 || 2.25" exterior sprocket diameter
|-
| A5 || [{UP}Parks12InchPlanerParts%2fP95_A5_shaftspacer.jpg|Shaft Spacer] || 0.18" wide || 1 || 
|-
| A6 || [{UP}Parks12InchPlanerParts%2fP95_A6_88toothgearslottedhub.jpg|88 Tooth Gear, Slotted Hub] || - || 1 || .75"ID
|-
| A7 || [{UP}Parks12InchPlanerParts/P95_A7_throwoutsleevebearing.jpg|Throw Out Sleeve Bearing] || .75"ID || 1 || 
|-
| A8 || [{UP}Parks12InchPlanerParts%2fP95_A8_throwoutsheeve.jpg|Throw Out Sleeve] || .75"ID, 1.125"OD || 1 || Sheeve: 1 5/32" inner diameter, 2" outer diameter
|-
| A9 || [{UP}Parks12InchPlanerParts%2fP95_A9_eccentricbracketstuds.jpg|Eccentric Bracket Studs] || 1" || 2 || 1/4 20 threads
|-
| A10 || [{UP}Parks12InchPlanerParts%2fP95_A10_eccentricbracket.jpg|Eccentric Bracket] || - || 1 || 
|-
| A11 || [{UP}Parks12InchPlanerParts%2fP95_A11_throwouthandle.jpg|Throw Out Handle] || ~8" || 1 || curved handle version
|-
| A12 || [{UP}Parks12InchPlanerParts%2fP95_A12_throwouteccentric.jpg|Throw Out Eccentric] || see comments || 1 || main: 2.125" x .75"OD, flange: 1"OD, stud: .375" x .50"OD
|-
| A13-20 || [{UP}Parks12InchPlanerParts%2fP95_A13_A14_A15_A16_A17_A18_A19_A20_gearboxassembly.jpg|Lower Gear Shaft Bearing] || .75"ID || 1 || part of gear shaft assembly
|-
| A13 || [{UP}Parks12InchPlanerParts/P95_A13_lowergearshaftbearing.jpg|Lower Gear Shaft Bearing] || - || 
|-
| A14 || [{UP}Parks12InchPlanerParts/P95_A14_88oothgearplainhub.jpg|88 Tooth Gear, Plain Hub] || .75"ID || 1 || 
|-
| A15 || [{UP}Parks12InchPlanerParts/P95_A15_shortgearshaft_earlier.jpg|Short Gear Shaft] || .50"OD and .75"OD || 1 || early style
|-
| A15 || [{UP}Parks12InchPlanerParts/P95_A15_shortgearshaft_later.jpg|Short Gear Shaft] || - || 1 || later style
|-
| A16 || [{UP}Parks12InchPlanerParts/P95_A16_gearshaftbearing.jpg|Gear Shaft Bearing] || .50"ID || 1 || 
|-
| A17 || [{UP}Parks12InchPlanerParts/P95_A17_20toothgear.jpg|20 Tooth Gear] || 1.0"OD, .50"ID || 3 || 1.375" external tooth diameter
|-
| A18 || [{UP}Parks12InchPlanerParts/P95_A18_gearshaftbearing.jpg|Gear Shaft Bearing] || .75"ID || 2 || 
|-
| A19 || [{UP}Parks12InchPlanerParts/P95_A19_longgearshaft.jpg|Long Gear Shaft] || .50"OD and .75"OD || 1 || 
|-
| A20 || [{UP}Parks12InchPlanerParts/P95_A20_128toothgear.jpg|128 Tooth Gear]
|| .75"ID || 1 || 
|-
| A21 || [{UP}Parks12InchPlanerParts%2fP95_A21_gearboxcover.jpg|Gear Box Cover] || 10" x 4" || 1 || 
|-
| A22 || [{UP}Parks12InchPlanerParts%2fP95_A22_gearboxcoverstuds.jpg|Gear Box Cover Studs] || .75" || 2 || 1/4 20 threads
|-
| A23 || [{UP}Parks12InchPlanerParts%2fP95_A23_smoothfeedroll.jpg|Smooth Feed Roll] || 24" (??) || 1 || need dimensions of various segments
|-
| A24 || Felt Washer || .75"OD || 1 || original entry machine has bearing cap gaskets, no washer
|-
| A25 || [{UP}Parks12InchPlanerParts%2fP95_A25_headshaftsleeve.jpg|Head Shaft Sleeve] || 1.375" long || 1 || .75"ID, need OD
|-
| A26 || [{UP}Parks12InchPlanerParts%2fP95_A26_headballbearingno3204.jpg|Head Ball Bearing #3204] || .75"ID || 2 || need bearing specs for replacements
|-
| A27 || [{UP}Parks12InchPlanerParts%2fP95_A27_headshaftspacer.jpg|Head Shaft Spacer] ||  || 1 || 
|-
| A28 || [{UP}Parks12InchPlanerParts%2fP95_A28_12inchheadwithshaft.jpg|Head with Shaft] || 24" long || 1 || need dimensions of various segments
|-
| A29 || [{UP}Parks12InchPlanerParts%2fP95_A29_slottedheadsetscrew.jpg|Hollow Head Set Screw] || - || 1 || v-pulley on original entry machine not factory
|-
| A30 || [{UP}Parks12InchPlanerParts%2fP95_A30_flutedfeedroll.jpg|Fluted Feed Roll] || 22" long || 1 || need dimensions of various segments
|-
| A31 || [{UP}Parks12InchPlanerParts%2fP95_A31_hollowheadsetscrew.jpg|Hollow Head Set Screw] || 1/2" head || 15 || gib screws for cutterhead
|-
| A32 || [{UP}Parks12InchPlanerParts%2fP95_A32_chipbreaker_gib.jpg|12" Chip Breaker] || 12" x 3/4" x 1/4" || 3 || 
|-
| A33 || [{UP}Parks12InchPlanerParts%2fP95_A33_HSSknives.jpg|12" HSS Knives] || 12" x 7/8" x 1/8" || 3 || someone please confirm
|-
| A34 || [{UP}Parks12InchPlanerParts%2fP95_A34_completerollerchain.jpg|Complete Roller Chain] || - || 1 || 
|-
| A35 || [{UP}Parks12InchPlanerParts%2fP95_A35_connectinglinkforchain.jpg|Connecting Link for Chain] || - || 1 || 
|-
| A36 || [{UP}Parks12InchPlanerParts%2fP95_A36_pressurebar.jpg|Pressure Bar] || - || 1 || 
|-
| A37 || [{UP}Parks12InchPlanerParts%2fP95_A37_hoodstud.jpg|Hood Stud] || - || 2 || 
|-
| A38 || [{UP}Parks12InchPlanerParts%2fP95_A38_shavinghoodtop.jpg|Shaving Hood] || - || 1 || View of Top
|-
| A38 || [{UP}Parks12InchPlanerParts%2fP95_A38_shavinghoodbottom.jpg|Shaving Hood] || - || 1 || View of Bottom
|-
| A39 || [{UP}Parks12InchPlanerParts%2fP95_A39_A40_adjustingstudforhood.jpg|Lock Nut for Hood] || - || 1 || 
|-
| A40 || [{UP}Parks12InchPlanerParts%2fP95_A39_A40_adjustingstudforhood.jpg|Adjusting Stud for Hood] || 1.25" || 1 || 1/4 20 threads
|-
| A41 || [{UP}Parks12InchPlanerParts%2fP95_A41_tableroller.jpg|Table Roller] || 12" x 1"OD || 1 || 
|-
| A42 || [{UP}Parks12InchPlanerParts%2fP95_A42_tablerollerbearing.jpg|Table Roller Bearing] || 1.625" x .75" x .50" || 1 || 
|-
| A43 || [{UP}Parks12InchPlanerParts%2fP95_A43_table.jpg|Table] || - || 1 || 
|-
| A44 || [{UP}Parks12InchPlanerParts%2fP95_A44_tablegib.jpg|Table Gib] || 4" x 1" x .125" || 2 || 
|-
| A45 || [{UP}Parks12InchPlanerParts%2fP95_A45_A46_giblocknutandstud.jpg|Lock Nut for Table Gib] || - || 6 || 
|-
| A46 || [{UP}Parks12InchPlanerParts%2fP95_A45_A46_giblocknutandstud.jpg|Lock Nut Stud] || 1" || 6 || 1/4 20 threads, slotted head
|-
| A47 || [{UP}Parks12InchPlanerParts%2fP95_A47_A48_tablerollerbearingadjustingstud.jpg|Table Roller Adjusting Stud] || 1.375" || 1 || 1/4 20 threads
|-
| A48 || [{UP}Parks12InchPlanerParts%2fP95_A47_A48_tablerollerbearingadjustingstud.jpg|Lock Nut for Table Roller] || - || 1 || 
|-
| A49 || [{UP}Parks12InchPlanerParts%2fP95_A52_A51_A74_A49_rollbearingstudassembly.jpg|3/8" Hex Nut 1" Long] || 1" || 6 || part of roller bearing stud assembly
|-
| A50 || [{UP}Parks12InchPlanerParts%2fP95_A50_springcollar.jpg|Spring Collar] || - || 6 || 
|-
| A51 || [{UP}Parks12InchPlanerParts%2fP95_A52_A51_A74_A49_rollbearingstudassembly.jpg|Compression Spring] || - || 6 || 
|-
| A52 || [{UP}Parks12InchPlanerParts%2fP95_A52_A51_A74_A49_rollbearingstudassembly.jpg|Roll Bearing Stud] || - || 4 || part of roller bearing stud assembly
|-
| A53 || [{UP}Parks12InchPlanerParts%2fP95_A53_A55_pressurebarstudassembly.jpg|Pressure Bar Stud] || - || 2 || part of pressure bar stud assembly
|-
| A54 || [{UP}Parks12InchPlanerParts%2fP95_A54_A70_smoothfeedrollbearing.jpg|Smooth Feed Roll Bearing] || - || 2 || specify right or left
|-
| A55 || [{UP}Parks12InchPlanerParts%2fP95_A53_A55_pressurebarstudassembly.jpg|Stud Collar] || - || 2 || part of pressure bar stud assembly
|-
| A56 || [{UP}Parks12InchPlanerParts%2fP95_A56_flutedfeedrollbearing.jpg|Fluted Feed Roll Bearing] || - || 2 || specify right or left
|-
| A57 || [{UP}Parks12InchPlanerParts%2fP95_A57_bearingcapstuds.jpg|Bearing Cap Stud] || 1" || 2 || 5/16 18 threads
|-
| A58 || [{UP}Parks12InchPlanerParts%2fP95_A58_A77_bearingcapandalemitefitting.jpg|Bearing Cap] || - || 2 || specify left or right
|-
| A59 || [{UP}Parks12InchPlanerParts%2fP95_A59_leftsidecasting.jpg|Left Side Casting] || - || - || 
|-
| A60 || [{UP}Parks12InchPlanerParts%2fP95_A60_rightsidecasting.jpg|Right Side Casting] || - || 1 || 
|-
| A61 || [{UP}Parks12InchPlanerParts%2fP95_A61_base.jpg|Base] || 19.5" x 14.5" || 1 || aluminum version, style #3
|-
| A62 || [{UP}Parks12InchPlanerParts%2fP95_A62_elevatingshaft.jpg|Elevating Shaft] || 20" long, .625" shaft || 1 || 
|-
| A63 || [{UP}Parks12InchPlanerParts%2fP95_A63_shaftcollar.jpg|Shaft Collar] || 5/8"ID || 4 || 
|-
| A64 || [{UP}Parks12InchPlanerParts%2fP95_A64_A65_elevatingscrewandgear.jpg|Bevel Gear L102] || - || 4 || 
|-
| A65 || [{UP}Parks12InchPlanerParts%2fP95_A64_A65_elevatingscrewandgear.jpg|Elevating Screw] || - || 2 || specify left or right
|-
|  || [{UP}Parks12InchPlanerParts%2fP95_elevatingshaftassembly.jpg|Elevating Shaft Assembly] || - || 1 || included to show parts orientation
|-
| A66 || [{UP}Parks12InchPlanerParts%2fP95_A66_columntierod.jpg|Column Tie Rod] || 16" long, .75" shaft || 2 || 
|-
| A67 || [{UP}Parks12InchPlanerParts%2fP95_A67_handwheeltop.jpg|Hand Wheel and Handle] || .625"ID || 1 || Top View
|-
| A67 || [{UP}Parks12InchPlanerParts%2fP95_A67_handwheelbottom.jpg|Hand Wheel and Handle] || .625"ID || 1 || Bottom View
|-
| A68 || [{UP}Parks12InchPlanerParts%2fP95_A68_wiredepthindicator.jpg|Depth Indicator] || - || 1 || bent wire style
|-
| A69 || [{UP}Parks12InchPlanerParts%2fP95_A69_depthscale.jpg|Depth Scale] || 4" scale || 1 || 
|-
| A70 || [{UP}Parks12InchPlanerParts%2fP95_A54_A70_smoothfeedrollbearing.jpg|1/4" oiler] ||  || 4 || installed on roll bearings
|-
| A71 || [{UP}Parks12InchPlanerParts%2fP95_A71_halfmoonkey.jpg|Half Moon Key] || - || 1 || for smooth feed roll shaft, under throw out sleeve
|-
| A72 || [{UP}Parks12InchPlanerParts%2fP95_A72_vpulley.jpg|3" v-pulley] || .75"ID || 1 || original entry machine shows smaller replacement pulley
|-
| A73 || [{UP}Parks12InchPlanerParts%2fP95_A74_jamnut3_8thick.jpg|Jam Nut 5/16" thick] || 5/16" thick || 2 || for pressure bar mount 
|-
| A74 || [{UP}Parks12InchPlanerParts%2fP95_A74_jamnut3_8thick.jpg|Jam Nut 3/16" thick] || 3/16" thick || 6 || for roll bearing and pressure bar studs 
|-
| A75 || [{UP}Parks12InchPlanerParts%2fP95_A75_A76_hexboltsandnuts.jpg|Hex Head Bolts] || 1.75" || 4 || 1/2 13 threads, for side casting mount on base
|-
| A76 || [{UP}Parks12InchPlanerParts%2fP95_A75_A76_hexboltsandnuts.jpg|Hex Nuts 1/2"x5/16"x7/8"] || - || 1 || 1/2 13 threads, for side casting mount on base
|-
| A77 || [{UP}Parks12InchPlanerParts%2fP95_A58_A77_bearingcapandalemitefitting.jpg|Alemite Fitting] || - || 1 || grease zerks for bearing caps
|-
| na || [{UP}Parks12InchPlanerParts%2fP95_drainplug.jpg|Drain Plug] || - || 1 || 
|-
| na || [{UP}Parks12InchPlanerParts%2fP95_Parkstag.jpg|Parks Machine Tag] || 3"x2" || 1 || 
|}
Meta Keywords:
Meta Description:
Change Comment:
	Welcome Guest, • Login
Wiki Home \| VintageMachinery.org Home \| OWWM.org Home \| Donate	Search the Wiki: »