Image
Welcome Guest, • Login
RSS RSS

Navigation






Search the wiki
»

PoweredBy


Table of Contents [Hide/Show]


Atlas
      63 15" Drill Press
Boice-Crane
      1400 6" Jointer
      1650 15" Bench Top Drill Press
      1000 12" Thickness Planer
Buffalo Forge
      No. 18 Drill Press (w/ external screw table lift)
Delta
      Unisaw
      14" Drill Press (DP220)
      15" Drill Press
      17" Drill Press
      7" Tool Grinder
      10" Grinder
      14" Bandsaw, Wood Cutting
      14" Bandsaw, Metal/Wood Cutting
      Delta/Crescent 20" Bandsaw (model 28-350 and 28-365 with rounded corner cabinet)
      Delta/Rockwell 8" Jointer (model 37-315)
      Delta/Rockwell 6" Jointer (model 37-220)
      Delta/Rockwell 4" Jointer (37-290, 37-110, 22-110)
      Delta 900 - Radial Arm Saw
      Delta Super 900 - Radial Arm Saw
      Red Star Pre-Delta Radial Arm Saw
      Delta/Rockwell 22-101 Planer
      46-111 14/11 Inch Lathe
      43-503 Pin Router
      Carbide Grinder
      Delta/Rockwell 10" Abrasive Cut-Off Saw
      Motor: Model 87-310 (2HP 3 phase)
      Motor: Model 86-520 (1/2 HP 3 phase)
      Motor: 3/4 hp 1725 rpm Repulsion Induction motor: frame 180
      Motor: Model 6400 - 1/3 hp 1725 rpm Repulsion Induction motor
      Motor: Model 62-110 - 1/3 hp 1725 rpm Capacitor Start motor
      Motor: Double Duty cat. V6920 - 1/2 hp 1725 rpm Capacitor Start motor: frame 165, 5/8" double-end shaft
      Motor: Double Duty cat. 62610 - 1/2 hp 1725 rpm Capacitor Start motor: frame 166, 5/8" double-end shaft
      Motor: Model 924 - 3/4 hp 1725 rpm Repulsion Induction motor
      Motor: Model 800 - 1/3 hp 1725 rpm Split Phase motor
Delta
      Unisaw
      14" Drill Press (DP220)
      15" Drill Press
      17" Drill Press
      7" Tool Grinder
      10" Grinder
      14" Bandsaw, Wood Cutting
      14" Bandsaw, Metal/Wood Cutting
      Delta/Crescent 20" Bandsaw (model 28-350 and 28-365 with rounded corner cabinet)
      Delta/Rockwell 8" Jointer (model 37-315)
      Delta/Rockwell 6" Jointer (model 37-220)
      Delta/Rockwell 4" Jointer (37-290, 37-110, 22-110)
      Delta 900 - Radial Arm Saw
      Delta Super 900 - Radial Arm Saw
      Delta/Rockwell 22-101 Planer
      46-111 14/11 Inch Lathe
      43-503 Pin Router
      Carbide Grinder
      Delta/Rockwell 10" Abrasive Cut-Off Saw (No. 1600)
      Motor: Model 93-610 (2HP, 1725 RPM, capacitor start)
      Motor: Model 87-310 (2HP 3 phase)
      Motor: Model 86-520 (1/2 HP 3 phase)
      Motor: 3/4 hp 1725 rpm Repulsion Induction motor: frame 180
      Motor: Model 6400 - 1/3 hp 1725 rpm Repulsion Induction motor
      Motor: Model 62-110 - 1/3 hp 1725 rpm Capacitor Start motor
      Motor: Double Duty cat. V6920 - 1/2 hp 1725 rpm Capacitor Start motor: frame 165, 5/8" double-end shaft
      Motor: Double Duty cat. 62610 - 1/2 hp 1725 rpm Capacitor Start motor: frame 166, 5/8" double-end shaft
      Motor: Model 924 - 3/4 hp 1725 rpm Repulsion Induction motor
      Motor: Model 800 - 1/3 hp 1725 rpm Split Phase motor
DeWalt
      MBC/MBF 9" Radial Arm Saws
Oliver
      192 18" Band Saw
Parks
      12" Planer
      M2 Bandsaw Wheels
Porter Cable
      G4 Belt Sander
Powermatic
      141 Bandsaw
      143 Bandsaw
       Model 100 12" planer (1958)
      Model 25 Shaper
      Model 30 Belt/Disk Sander
      Model 1200 20" Drill Press (early model)
      Model 50 6" Jointer
Sprunger Bros.
      NDP15 Drill Press (floor and bench models)
State Manufacturing & Engineering Co.
      B-4 Oscillating Spindle Sander and T-5 Titling Spindle Sander
Walker-Turner
      1180B 10" Tilting Arbor Table Saw
      14" Wood Bandsaw
      Drill Press - Model 1100 20"
      Early 700 Series 1/2" Shaper
Wissota
      701 Series A Belt-Driven Grinder


Accurate Bearings comes highly recommended on the forum for replacements.

Atlas

63 15" Drill Press

  • Quill: 6202-5/8 bore, Spindle pulley: 6204 & 6205

Boice-Crane

1400 6" Jointer

  • 6203-LL (17mm B, 40mm OD, 12mm W)

1650 15" Bench Top Drill Press

Photo Index for this type drill press

The following are the two upper bearings for the spindle. They are located just below the spindle sheave:

  • 6005-LL (25mm B, 47mm OD, 12mm W)
  • 6005-LLNR with Snap Ring (25mm B, 47mm OD, 12mm W)

Both of these bearings are available through Accurate Bearing.

1000 12" Thickness Planer

  • 1305 Double Row Self Aligning Ball Bearing (Qty. 2 on cutter head)

Buffalo Forge

No. 18 Drill Press (w/ external screw table lift)

  • Quill:
    • Upper: 88505 ND > 88505 KS
    • lower: 55505 ND > 5205 ZZ TS
  • Pulley:
    • Upper: 88508 ND > 88508 IF
    • Lower: 88508 ND > 88508 IF
  • Lift table:
    • 5449 Nice > 3066 HV (3 required)



Delta

Unisaw

  • Bullet Motor: 87504 (x2)

  • 87-318 2HP 3ph 1968 Motor: MRC 205 SZZ (x2) (original?)

  • 87-010 Motor (x2):
    • Original: Norma S 3505
    • Replacement: KYK 63205



Note: I have a 1947 motor that says frame 180 Catalog No 87-010 and it takes New Departure 87504. Given this conflict with the above data it might be best to wait until the motor is open before buying bearings.

  • Arbor (x2):
    • Older style with narrow (~.325 in) spacers: 88503 (bearing has extended inner race)
    • Newer style with wider (~.471 in) spacers: 6203 (bearing does not have extended inner race)



14" Drill Press (DP220)

  • 2x 6202-10 (5/8" bore) for quill. These are not exact replacements as the original quill bearings were designed such that you could easily replace the quill with other designed for mortising or shaping, but for drill-only purposes these are suitable replacements. Original bearings' inner race is designed for a slip fit; newer 6202-5/8 bearings will have to be pressed on the spindle instead which makes the spindle non-interchangeable.
  • Pulley bearings are hard to find. Consider cleaning and reusing or ordering from Richard

15" Drill Press

  • Quill - 2x 6203
  • Pulley - 2x 6205

17" Drill Press

  • Lower Spindle (Inside Quill) - 87503 (x2) (Early Production) or 6203 (x2) (Late Production)
  • Upper Spindle Top Bearing - 487503 includes installed snap ring around OD
  • Upper Spindle Lower Bearing - 88503

7" Tool Grinder

  • Older Style:
    • 2x 88503
  • Newer Style:
    • 2x 6203
  • 2x48" Belt Attachment
    • 2x 6203

10" Grinder

  • 2x 6206

14" Bandsaw, Wood Cutting

  • Newer Style:
    • Upper wheel: 6202LL Nachi (2x)
    • Lower wheel: 6204LL Nachi (2x)
    • Blade guide thrust bearings: 6200LL Nachi (2x)
  • Older Style:
    • Upper wheel: 87502 (2x)
    • Lower wheel: 87504 (2x)
    • Blade guide thrust bearings: 6200LL Nachi (2x)

14" Bandsaw, Metal/Wood Cutting

  • Older Style (w/ turn lever selector):
    • Upper wheel: 87502 (2x)
    • Lower wheel: 87504 (2x)
    • Blade guide thrust bearings: 6200 (2x)
    • Gear case: 87016 (4x)
    • Input shaft oil seal: CR6229 (1x)

Delta/Crescent 20" Bandsaw (model 28-350 and 28-365 with rounded corner cabinet)

  • Upper wheel:
    • one 87504, one 87502
  • Lower wheel:
    • one 87506, one 87505
  • Thrust bearings: 6203

Delta/Rockwell 8" Jointer (model 37-315)

  • 6204

Delta/Rockwell 6" Jointer (model 37-220)

  • New Departure 87502
  • New Departure 87503
    • Extended inner race goes on cutterhead side

Delta/Rockwell 4" Jointer (37-290, 37-110, 22-110)

  • New Departure 87502 (x2)
    • Extended inner race faces the inside on both sides.

Delta 900 - Radial Arm Saw

  • Motor Bearings for 3/4 HP Frame 159Y:
    Arbor (Blade) Side Motor Bearing: MRC 204 FSF
    Back Side Motor Bearing: 87013

Delta Super 900 - Radial Arm Saw

  • Rollerhead (x4):Nachi 81004

Red Star Pre-Delta Radial Arm Saw

  • Model 40A 1.5HP Motor
    Arbor blade side bearing: Norma 205PP ID,OD,W = 25mm, 52mm, 15mm
    Back Side Motor bearing: Norma 303PP ID,OD,W = 17mm, 47mm, 14mm

Delta/Rockwell 22-101 Planer

  • Cutter Head: 6205 (newer model w/ no extended inner race)
  • Infeed/Outfeed Roller O-Ring: 22mm ID x 24mm OD (approximate)
  • NICE thrust bearing in gear box #5774(2) required

46-111 14/11 Inch Lathe

  • 87505 (x2) (extended inner race faces out on both sides)

43-503 Pin Router

  • Spindle bearings
    • 88504 20mm bore 47mm O.D. .6250 inch thickness
    • 87501 12mm bore 32mm O.D. .500 inch thickness

Carbide Grinder

  • New style:
    • 6203 x 2

Delta/Rockwell 10" Abrasive Cut-Off Saw

  • Arbor: MRC203FSF x 2 (87503 equivalent - extended inner race)
    ====Motor: Model 93-610 (2HP, 1725 RPM, capacitor start)====

  • 6203 (ODE)
  • 6204 (DE)

Motor: Model 87-310 (2HP 3 phase)

  • 6204 (ODE)
  • 6204 (DE)

Motor: Model 86-520 (1/2 HP 3 phase)

  • 87504 (x2)

Motor: 3/4 hp 1725 rpm Repulsion Induction motor: frame 180

  • Extended race face in: 87504 (x2)

Motor: Model 6400 - 1/3 hp 1725 rpm Repulsion Induction motor

  • Extended inner race: 87502 (x2)
    NOTE: Inner race is positioned toward the inside of motor

Motor: Model 62-110 - 1/3 hp 1725 rpm Capacitor Start motor

  • Extended inner race: 87016 (x2)
    NOTE: Inner race is positioned toward the inside of motor
  • Alternative: 6203 (x2)
    My 62-110 used these.
  • 62-110 scroll saw motor
    NACHI 6203zz no extended race

Motor: Double Duty cat. V6920 - 1/2 hp 1725 rpm Capacitor Start motor: frame 165, 5/8" double-end shaft

  • 87016 (x2), Has one side extended inner ring. The bore is 16mm (.6299"), the OD is 35mm (1.378").
    NOTE: The inner ring extended side is positioned toward the inside of motor.
  • Alternative: The special bore size 6202-16 bearing can work if a .067" thick spacer is used.

Motor: Double Duty cat. 62610 - 1/2 hp 1725 rpm Capacitor Start motor: frame 166, 5/8" double-end shaft

Same as V6920: two 87016 bearings.

Motor: Model 924 - 3/4 hp 1725 rpm Repulsion Induction motor

  • Extended inner race: 87504 (x2)
    NOTE: Inner race is positioned toward the inside of motor

Motor: Model 800 - 1/3 hp 1725 rpm Split Phase motor

  • Extended inner race: 87502 (x2)
    NOTE: Inner race is positioned toward the inside of motor





Delta

Unisaw

  • Bullet Motor: 87504 (x2)

  • 87-010 Motor (x2):
    • Original: Norma S 3505
    • Replacement: KYK 63205



Note: I have a 1947 motor that says frame 180 Catalog No 87-010 and it takes New Departure 87504. Given this conflict with the above data it might be best to wait until the motor is open before buying bearings.

  • Arbor (x2):
    • Older style with narrow (~.325 in) spacers: 88503 (bearing has extended inner race)
    • Newer style with wider (~.471 in) spacers: 6203 (bearing does not have extended inner race)

14" Drill Press (DP220)

  • 2x 6202-10 (5/8" bore) for quill. These are not exact replacements as the original quill bearings were designed such that you could easily replace the quill with other designed for mortising or shaping, but for drill-only purposes these are suitable replacements. Original bearings' inner race is designed for a slip fit; newer 6202-5/8 bearings will have to be pressed on the spindle instead which makes the spindle non-interchangeable.
  • Pulley bearings are hard to find. Consider cleaning and reusing or ordering from Richard

15" Drill Press

  • Quill - 2x 6203
  • Pulley - 2x 6205

17" Drill Press

  • Lower Spindle (Inside Quill) - 87503 (x2) (Early Production) or 6203 (x2) (Late Production)
  • Upper Spindle Top Bearing - 487503 includes installed snap ring around OD
  • Upper Spindle Lower Bearing - 88503

7" Tool Grinder

  • Older Style:
    • 2x 88503
  • Newer Style:
    • 2x 6203
  • 2x48" Belt Attachment
    • 2x 6203

10" Grinder

  • 2x 6206

14" Bandsaw, Wood Cutting

  • Newer Style:
    • Upper wheel: 6202LL Nachi (2x)
    • Lower wheel: 6204LL Nachi (2x)
    • Blade guide thrust bearings: 6200LL Nachi (2x)
  • Older Style:
    • Upper wheel: 87502 (2x)
    • Lower wheel: 87504 (2x)
    • Blade guide thrust bearings: 6200LL Nachi (2x)

14" Bandsaw, Metal/Wood Cutting

  • Older Style (w/ turn lever selector):
    • Upper wheel: 87502 (2x)
    • Lower wheel: 87504 (2x)
    • Blade guide thrust bearings: 6200 (2x)
    • Gear case: 87016 (4x)
    • Input shaft oil seal: CR6229 (1x)

Delta/Crescent 20" Bandsaw (model 28-350 and 28-365 with rounded corner cabinet)

  • Upper wheel:
    • one 87504, one 87502
  • Lower wheel:
    • one 87506, one 87505
  • Thrust bearings: 6203

Delta/Rockwell 8" Jointer (model 37-315)

  • 6204

Delta/Rockwell 6" Jointer (model 37-220)

  • New Departure 87502
  • New Departure 87503
    • Extended inner race goes on cutterhead side

Delta/Rockwell 4" Jointer (37-290, 37-110, 22-110)

  • New Departure 87502 (x2)
    • Extended inner race faces the inside on both sides.

Delta 900 - Radial Arm Saw

  • Motor Bearings for 3/4 HP Frame 159Y:
    Arbor (Blade) Side Motor Bearing: MRC 204 FSF
    Back Side Motor Bearing: 87013

Delta Super 900 - Radial Arm Saw

  • Rollerhead (x4):Nachi 81004

Delta/Rockwell 22-101 Planer

  • Cutter Head: 6205 (newer model w/ no extended inner race)
  • Infeed/Outfeed Roller O-Ring: 22mm ID x 24mm OD (approximate)
  • NICE thrust bearing in gear box #5774(2) required

46-111 14/11 Inch Lathe

  • 87505 (x2) (extended inner race faces out on both sides)

43-503 Pin Router

  • Spindle bearings
    • 88504 20mm bore 47mm O.D. .6250 inch thickness
    • 87501 12mm bore 32mm O.D. .500 inch thickness

Carbide Grinder

  • New style:
    • 6203 x 2

Delta/Rockwell 10" Abrasive Cut-Off Saw (No. 1600)

  • 5/8" Arbor Assembly: 87503 (x2) (extended inner race faces out on both sides)

Motor: Model 93-610 (2HP, 1725 RPM, capacitor start)

  • 6203 (ODE)
  • 6204 (DE)

Motor: Model 87-310 (2HP 3 phase)

  • 6204 (ODE)
  • 6204 (DE)

Motor: Model 86-520 (1/2 HP 3 phase)

  • 87504 (x2)

Motor: 3/4 hp 1725 rpm Repulsion Induction motor: frame 180

  • Extended race face in: 87504 (x2)

Motor: Model 6400 - 1/3 hp 1725 rpm Repulsion Induction motor

  • Extended inner race: 87502 (x2)
    NOTE: Inner race is positioned toward the inside of motor

Motor: Model 62-110 - 1/3 hp 1725 rpm Capacitor Start motor

  • Extended inner race: 87016 (x2)
    NOTE: Inner race is positioned toward the inside of motor
  • Alternative: 6203 (x2)
    My 62-110 used these.
  • 62-110 scroll saw motor
    NACHI 6203zz no extended race

Motor: Double Duty cat. V6920 - 1/2 hp 1725 rpm Capacitor Start motor: frame 165, 5/8" double-end shaft

  • 87016 (x2), Has one side extended inner ring. The bore is 16mm (.6299"), the OD is 35mm (1.378").
    NOTE: The inner ring extended side is positioned toward the inside of motor.
  • Alternative: The special bore size 6202-16 bearing can work if a .067" thick spacer is used.

Motor: Double Duty cat. 62610 - 1/2 hp 1725 rpm Capacitor Start motor: frame 166, 5/8" double-end shaft

Same as V6920: two 87016 bearings.

Motor: Model 924 - 3/4 hp 1725 rpm Repulsion Induction motor

  • Extended inner race: 87504 (x2)
    NOTE: Inner race is positioned toward the inside of motor

Motor: Model 800 - 1/3 hp 1725 rpm Split Phase motor

  • Extended inner race: 87502 (x2)
    NOTE: Inner race is positioned toward the inside of motor





DeWalt

MBC/MBF 9" Radial Arm Saws

  • Motor (1ph and 3ph):
    • Arbor side: 88504
    • Cord side: Original: Fafnir 200KLL2
    • Cord side: Replacement: JAF 88500
      (The GWI saw has the same motor bearings)

  • Rollerhead (x4):
    • Original: Fafnir 200KDD15
    • Replacement: Nachi 81004

Oliver

192 18" Band Saw

  • Howell Electric Co 1hp 3ph Motor:
    • 2x 6306

Parks

12" Planer

  • 2x 6204

M2 Bandsaw Wheels

  • Upper - Originals 202KD, Replacement 6202ZZ
  • Lower - Originals 204KD, Replacement 6204ZZ

Porter Cable

G4 Belt Sander

  • Motor: 2x 6205
  • Sander upper wheel: 2x5203 and 2x6203

Powermatic

141 Bandsaw

  • Top: 2x 6203LLNR
  • Bottom 2x 6204LLNR
  • Guides 4x 6200LL

143 Bandsaw

  • Top: 2x 6203LLNR
  • Gear Box:
    • 3x 6303LL
    • 1x RB012AZZ (this crosses to a NPC012RP)
    • 3x TRB 1220
    • 3x IR 1212
    • 3x IR 1216
  • Guides 4x 6200LL
  • Countershaft 2x 6204LLNR
  • Tension Adjustment Nice 603 1/4



Model 100 12" planer (1958)

                         Original        Interchange #    Bore x O.D. x width     Qty

Cutterhead          Fafnir 206KLL          88506         30mm x 62mm x .945"       2
Table elev screws   Nice 605 (thrust)      4457-00       5/8" x 1 1/8" x .34"      2
Motor               Fafnir W203PP          63203         17mm x 40mm x 17.5mm      1
Motor               Norma 3605             63305         25mm x 62mm x 25.4mm      1
Oilite bushing, drive pulleys                            3/4" x 7/8" x 3/4"        4
Oilite bushing, main pulley                              5/8" x 3/4" x 1"          2
Oilite bushing, table rollers                            5/8" x 3/4" x 1"          4

Model 25 Shaper

  • Spindle: 1x 6205, 1x 6304



Model 30 Belt/Disk Sander

  • Idler 2x 6205LLNR (snap ring)
  • Quill 2x W205PP













Model 1200 20" Drill Press (early model)

  • quill: 2x 6206
  • idler: 2x 6205, 1x 6204
  • spindle: 2x 6007



Model 50 6" Jointer

  • Cutterhead: 2x 6203



Sprunger Bros.

NDP15 Drill Press (floor and bench models)

link to photo index for this model machine
  • Quill bearings: 2X 1623 Inch 0.6250" X 1.3750" X 0.4375" (double sealed or double shielded)
  • Spindle drive bearings: 2X 6205 Metric 25mm X 52mm X 15mm (double sealed or double shielded)



State Manufacturing & Engineering Co.

B-4 Oscillating Spindle Sander and T-5 Titling Spindle Sander

Oscillating Mechanism:

  • Upper (p/n 018026): 6205
  • Lower (p/n 018027): 6204



Walker-Turner

1180B 10" Tilting Arbor Table Saw

  • Arbor Cartridge: 6204-3/4 bore (x2)

14" Wood Bandsaw

  • Upper Wheel: 6202 LL 5/8 bore
  • Lower Wheel: 6204 LL 3/4 bore

Drill Press - Model 1100 20"

There are several variations of this press, some of which use Walker-Turner specific bearings (mostly with inch bores), some of which use standard bearings. Be careful when measuring!

  • Pulley: 2x 6205
  • Upper Spindle: 6204-3/4
  • Lower Spindle: 5205 - not exact match, but close
  • These are preliminary and have not yet been verified.

Early 700 Series 1/2" Shaper

Like this one
  • Shaper spindle: 6203 (x2)

Wissota

701 Series A Belt-Driven Grinder

  • 6203 (2 req'd, Original-double shield, Replacements-double shields or seals)

ScrewTurn Wiki version 3.0.5.600. Some of the icons created by FamFamFam.