Page History: Parks 12" Planer Parts and Photo Index
Compare Page Revisions
Page Revision: 2008/05/11 00:55
by Bill Nance--====STILL UNDER CONSTRUCTION====
Introduction
The Parks 95 12" planer, as described on other pages within this wiki, is a well-respected vintage planer, manufactured across several decades by Parks Woodworking Machine Company, with a fairly consistent design throughout its history. This page provides an index of parts for a Parks Model 95 planer, including photographs and dimensions where available.
The original entry data and photographs are drawn from a restoration of machine #5401-, which is believed to have been manufactured in the early 1940s. The parts numbers are mapped to the exploded parts diagram and parts list from the
1949 Operating Instructions and Parts List for Parks 12" Thickness Planer found in the OWWM Publication Reprints. Others who wish to edit this entry with additional information should indicate in the comments section below any information that references a different operating manual. Please note that in the original entry, some parts were not included in the machine that was restored, and some parts were not disassembled and either may not be photographed or may be shown as a component of an assembly. Others are encouraged to edit/replace with individual parts as available.
Parks Model 95 Parts Index
Part# | Part Name | Dimensions | Qty | Comments |
A1 | Gear Box (Casting Only) | - | 1 | "Three hump" cast iron model |
A2 | Shaft Collar | .75"ID, 1.25"OD | 3 |
A3 | Hollow Head Set Screw | 3/16" head | ? | |
A4 | 12 Tooth Sprocket | .75"ID, 1.37"OD | 2 | 2.25" exterior sprocket diameter |
A5 | Shaft Spacer | 0.18" wide | 1 | |
A6 | 88 Tooth Gear, Slotted Hub | - | 1 | .75"ID |
A7 | Throw Out Sleeve Bearing | .75"ID | 1 | |
A8 | Throw Out Sleeve | .75"ID, 1.125"OD | 1 | Sheeve: 1 5/32" inner diameter, 2" outer diameter |
A9 | Eccentric Bracket Studs | 1" | 2 | 1/4 20 threads |
A10 | Eccentric Bracket | - | 1 | |
A11 | Throw Out Handle | ~8" | 1 | curved handle version |
A12 | Throw Out Eccentric | see comments | 1 | main: 2.125" x .75"OD, flange: 1"OD, stud: .375" x .50"OD |
A13 | Lower Gear Shaft Bearing | .75"ID | 1 | part of lower gear shaft assembly |
A14 | 88 Tooth Gear, Plain Hub | .75"ID | 1 | part of short gear shaft assembly |
A15 | Short Gear Shaft | .50"OD and .75"OD | 1 | part of short gear shaft assembly |
A16 | Gear Shaft Bearing | .50"ID | 1 | part of short gear shaft assembly |
A17 | 20 Tooth Gear | 1.0"OD, .50"ID | 3 | 1.375" external tooth diameter |
A18 | Gear Shaft Bearing | .75"ID | 2 | part of short and long gear shaft assemblies |
A19 | Long Gear Shaft | .50"OD and .75"OD | 1 | part of long gear shaft assembly |
A20 | 128 Tooth Gear | .75"ID | 1 | part of long gear shaft assembly |
A21 | Gear Box Cover | 10" x 4" | 1 | |
A22 | Gear Box Cover Studs | .75" | 2 | 1/4 20 threads |
A23 | Smooth Feed Roll | 24" (??) | 1 | need dimensions of various segments |
A24 | Felt Washer | .75"OD | 1 | original entry machine has bearing cap gaskets, no washer |
A25 | Head Shaft Sleeve | 1.375" long | 1 | .75"ID, need OD |
A26 | Head Ball Bearing #3204 | .75"ID | 2 | need bearing specs for replacements |
A27 | Head Shaft Spacer | .75"OD | 1 | not on original entry machine |
A28 | Head with Shaft | 24" long | 1 | need dimensions of various segments |
A29 | Hollow Head Set Screw | - | 1 | original entry v-pulley not factory |
A30 | Fluted Feed Roll | 22" long | 1 | need dimensions of various segments |
A31 | Hollow Head Set Screw | 1/2" head | 15 | gib screws for cutterhead |
A32 | 12" Chip Breaker | 12" x 3/4" x 1/4" | 3 | |
A33 | 12" HSS Knives | 12" x 7/8" x 1/8" | 3 | someone please confirm |
A34 | Complete Roller Chain | - | 1 | |
A35 | Connecting Link for Chain | - | 1 | |
A36 | Pressure Bar | - | 1 | |
A37 | Hood Stud | - | 2 | forgot to take pics of these |
A38 | Shaving Hood | - | 1 | View of Top |
A38 | Shaving Hood | - | 1 | View of Bottom |
A39 | Lock Nut for Hood | - | 1 | |
A40 | Adjusting Stud for Hood | 1.25" | 1 | 1/4 20 threads |
A41 | Table Roller | 12" x 1"OD | 1 | |
A42 | Table Roller Bearing | 1.625" x .75" x .50" | 1 | |
A43 | Table | - | 1 | |
A44 | Table Gib | 4" x 1" x .125" | 2 | |
A45 | Lock Nut for Table Gib | - | 6 | |
A46 | Lock Nut Stud | 1" | 6 | 1/4 20 threads, slotted head |
A47 | Table Roller Adjusting Stud | 1.375" | 1 | 1/4 20 threads |
A48 | Lock Nut for Table Roller | - | 1 | |
A49 | 3/8" Hex Nut 1" Long | 1" | 6 | part of roller bearing stud assembly |
A50 | Spring Collar | - | 6 | not included on original entry machine |
A51 | Compression Spring | - | 6 | |
A52 | Roll Bearing Stud | - | 4 | part of roller bearing stud assembly |
A53 | Pressure Bar Stud | - | 2 | part of pressure bar stud assembly |
A54 | Smooth Feed Roll Bearing | - | 2 | specify right or left |
A55 | Stud Collar | - | 2 | part of pressure bar stud assembly |
A56 | Fluted Feed Roll Bearing | - | 2 | specify right or left |
A57 | Bearing Cap Stud | 1" | 2 | 5/16 18 threads |
A58 | Bearing Cap | - | 2 | specify left or right |
A59 | Left Side Casting | - | - | |
A60 | Right Side Casting | - | 1 | |
A61 | Base | 19.5" x 14.5" | 1 | aluminum version, style #3 |
A62 | Elevating Shaft | 20" long, .625" shaft | 1 | |
A63 | Shaft Collar | 5/8"ID | 4 | forgot to take photos |
A64 | Bevel Gear L102 | - | 4 | |
A65 | Elevating Screw | - | 2 | specify left or right |
| Elevating Shaft Assembly | - | 1 | included to show parts orientation |
A66 | Column Tie Rod | 16" long, .75" shaft | 2 | |
A67 | Hand Wheel and Handle | .625"ID | 1 | Top View |
A67 | Hand Wheel and Handle | .625"ID | 1 | Bottom View |
A68 | Depth Indicator | - | 1 | bent wire style |
A69 | Depth Scale | 4" scale | 1 | |
A70 | 1/4" oiler | 1.25" | 1 | |
A71 | | 1.25" | 1 | |
A72 | | 1.25" | 1 | |
A73 | | 1.25" | 1 | |
A74 | | 1.25" | 1 | |
A75 | | 1.25" | 1 | |
A76 | | 1.25" | 1 | |
A77 | | 1.25" | 1 | |